大家都知道衛(wèi)生間地面裝修不能選擇濟南塑膠地板,必須使用地磚,那么怎么鋪地磚呢?具體流程是怎樣呢?以及鋪地磚的注意事項都有哪些?筑邦建材小編為此給大家做出了詳細的介紹:

As we all know, bathroom floor decoration can not choose Ji'nan plastic floor. We must use floor tiles. So how do we spread floor tiles? What is the specific process and what are the matters needing attention in the laying of floor tiles?

1.一是墻磚應從下向上鋪貼,且一面墻不能一次貼到頂,接縫一般為1——3毫米;二是鋪貼前要先處理墻面的平整,處理裂縫;三是粘結材料的涂抹要中間稍高于四周,用橡膠錘敲擊表面以固定,這樣一來可以避免空氣積存于粘結層中.同時要進行水平檢測;四是粘結材料要挑和適當,一般墻面水泥與沙比例為1:4,地面水泥與沙比例為1:3

The 1. one is the wall should be to be paved on the side of the wall, and not once posted on the top, seam is generally 1 - 3 mm; the two is paving before dealing with the wall leveling treatment crack; bonding material three is applied to the middle slightly higher than the surrounding with a rubber hammer surface by fixing this way to avoid air accumulation in the adhesive layer. At the same time to detect the level of four; a bonding material is to choose and appropriate, general wall cement sand ratio 1:4, ground cement and sand ratio of 1:3

2.地面要打平.有一些土建地面是不平的,遇到這種情況大家應該把不平的地方用水泥沙漿鋪平.鋪設時可以用不同的色彩的瓷磚(較深色的)把周圍框起來,而框內的瓷磚用較淺色的.當然,廚房跟廁所的地面一定要有傾斜度,這樣是為了方便排水.

2. the ground to draw. Some construction ground is uneven, encounter this kind of situation you should put where uneven cement mortar paving. Can use different colors when laying tiles (darker) around the frame, and the frame of ceramic tile with a lighter. Of course, the kitchen and toilet ground must to tilt, it is in order to facilitate drainage.

3.瓷磚裝修另一個要注意的是防水層的處理.在廚廁之些地方的墻面更應高度注意.因為更換瓷片通常會破壞原有水泥沙槳防水層.補救辦法是在貼設瓷磚前先打一層瀝青防水層.瓷磚之間的縫填白水泥也應補好:

The 3. tile decoration on another note is a waterproof layer. In some parts of the wall of the kitchen should be more attention. Because the replacement tiles will usually destroy the original cement sand pitch waterproof layer. The remedy is in the attached tile before the first hit a layer of asphalt waterproof layer seam filling. White water mud between the tiles it should be repaired:

4.磚面要鑲平,角度要準確,接口要對線;瓷磚在使用前要浸水半日;廁所地面要有適當斜面,不可積水 瓷磚接口掃白水泥后要用藤絲刷凈白水泥,不可在磚面上留有水泥污漬;地磚鋪徹完后要用紙板等覆蓋磚面,并至少24小時后才能在磚面上行走;

4. blocks to embed Ping, point to be accurate interface to the line; the tiles to inundate half day before use; toilet floor to have the appropriate slope, water can not be tile interface and white cement after use can brush whitening cement, can not be left in the brick surface cement stains; floor tile with cardboard etc. covered with brick after penetration, and at least 24 hours before the brick surface running;

5.先將平面掃凈濕潤,用1:3水泥砂漿打底,厚6毫米.墻面要略微帶毛,但必須平整.要計算縱橫塊數,定出水平分格.打完底后隔3-4天開始粘貼瓷磚.貼瓷磚時要先澆水濕潤墻,在下面一層瓷磚底部放好墊尺板,墊尺板必須保持水平線,并將它固定好. 瓷磚應預先浸透水分取出稍陰干,由墊尺板上沿著往上貼.在1:2水泥細砂中加入適量3-4%107膠,可改善砂漿的和易性.減緩凝結時間.以方便粘貼和防止砂漿流淌.

5. the plane sweep wet, backing with 1:3 cement mortar, 6 mm thick. The walls of microstrip hair, but must be smooth. To calculate the number of vertical and horizontal, set the level of division. After every 3-4 days after the end of paste tiles. Tiles to water wall in the bottom layer of the bottom tile the Department put the ruler pad plate, plate pad feet must remain horizontal line, and it will be fixed. The tiles should be pre soaked water out slightly dried by the ruler pad board along the paste up. Adding 3-4%107 glue in 1:2 cement fine sand, can improve the workability. The setting time to slow down. Easy to paste and prevent mortar flowing.

將砂漿抹于瓷磚背面,貼上墻上用橡皮錘輕敲磚面,使灰漿擠滿.貼完底層一層瓷磚后,將靠尺垂直放置作為豎向標準.貼時一般從陽角開始,以便不成整塊的瓷磚對齊縫.所有縱橫縫都須對齊,磚面沾著的灰漿應在未干時擦掉,貼完后用清水沖洗擦凈,縫子用白水泥擦干. 在水泥砂漿抹灰墻上貼瓷磚 在墻面上找出縱橫基準線,算好層數,接著再用摻入5-7%107膠的水泥素漿粘貼.如墻面很平整,先用純水泥漿掃一遍,在其沒干時開始粘貼.因粘結層不摻砂,故很薄,只有2-3毫米厚,粘結時易于平整,所以這是一種很方便經濟的方法.

The mortar on the back of the tile, the wall affixed with a rubber hammer on the tile surface, the mortar had finished bottom. With a layer of ceramic tile, will be on foot placed vertically as vertical standard. Stick from the positive angle, so as not to align the whole tile seam. All joints shall be aligned vertically and horizontally, brick surface with the mortar should be wiped in the wet, paste after rinse clean, nuiko with white cement dry. Tiles on the cement mortar on the wall to find the horizontal datum line on the wall, a good number, followed by incorporation of 5-7%107 adhesive cement paste. If the wall is very smooth, with pure water the mud swept again, began to paste on its not dry. Because of the bonding layer with sand, so it is very thin, only 2-3 mm thick, smooth and easy bonding, so this method is very convenient and economic.

6.設置地面標準高度面

6. set the ground standard height surface

(1)在刷干凈的地面上,攤鋪一層1:3.5的水泥砂漿,厚度小于10毫米.

(1) spread a layer of 1:3.5 cement mortar on the brushed ground, with a thickness of less than 10 millimeters.

(2)用尼龍線或棉線繩在墻面標高點上拉出地面標高線,以及垂直交叉的定位線.

(2) use nylon wire or cotton wire rope to pull out the ground standard line at the wall elevation point, and the vertical cross positioning line.

(3)按定位線的位置鋪貼瓷磚.用1:2的水泥砂漿攤在瓷磚背面上,再將瓷磚與地面鋪貼,并用橡皮錘敲擊瓷磚面,使其與地面壓實,并且高度與地面標高線吻合.鋪貼8塊以上時應用水平尺檢查平整度,對高的部分用橡皮錘敲平,低的部分應起出瓷磚后用水泥漿墊高.瓷磚的鋪貼程序,對于小房間來說(面積小于40平方米),通常是做T字形標準高度面.對于房間面積較大時通常按在房間中心十字形做出標準高度面,這樣可便于多人同時施工.

(3) according to the positioning line position of the paving tile. With 1:2 cement mortar stalls in the back of the tile, the tile and paving the ground, and with a rubber hammer to the ground tile surface, compaction, and height and ground elevation line well. Paving 8 blocks or more application level check Ping on the whole, the high part with a rubber hammer flat, the lower part of a ceramic tile should play with cement pad high. Tile paving procedures for small rooms (area less than 40 square meters), is usually done T shaped surface. The standard height room area is larger in the center of the room is usually the cross made standard height, which can facilitate the construction of the people at the same time.

7.鋪貼大面

7. paving face

鋪貼大面施工是以鋪好的標準高度面為標基進行,鋪貼時緊靠已鋪好的標準高度面開始施工,并用拉出的對縫平直線來控制瓷磚對縫的平直.鋪貼時水泥漿應飽滿的抹干瓷磚背面,并用橡皮錘敲實,以防止空鼓現象.并且一邊鋪貼一邊用水平尺檢查校正.并即刻擦去表面的水泥漿.

Paving surface construction is based on the standard height of surface paved standard medium, paving close to the paved surface of standard height to start construction, with straight and flat out to control on the butt. Tile paving cement slurry should be full wipe the back of the tile, and with a rubber hammer actually, in order to prevent the hollowing phenomenon. And while paving the side with the level check correction. And immediately wipe the surface of the cement slurry.

對于衛(wèi)生間、洗手間的地面,應注意鋪貼時做出1:500的返水斜度.

For the floor of toilet and bathroom, attention should be paid to the slope of 1:500 back water when paving.

整幅地面鋪貼完畢后,養(yǎng)護2天后,再進行抹縫施工.抹縫時,將白水泥調成干性團,在縫隙上擦抹,使瓷磚的對縫內填滿白水泥,再將瓷磚表面擦凈.

The ground floor after curing for 2 days, then wipe seam construction. Wipe seam, the white cement mixed into dry, wipe in the gap, so that the tiles on the inside is filled with white cement, and then wipe the surface of the tile.